Cable set for Phaserunner motor controller

Here you will find suitable cable sets for the Phaserunner – for connection to the Bafang BBSHD motor and much more.

SKU: 3100-VHA

Price range: 30,24 € through 40,33 € incl. VAT, plus shipping

All prices include EU import duties and sales tax — no additional payment required upon delivery (applies to deliveries within the EU)
Shipped from the EU warehouse
Advice and warranty service through your dealer in Austria
Verfügbar

Payment methods:

Kompatibel mit
Typ / Verwendung
Brand

Various cable sets for the Phaserunner from Grin

These cable sets are suitable for use with the Phaserunner motor controller.

Various cable sets – simply select above:

1) Battery cable only

  • approx. 80 cm High Flex battery cable XT60 to Anderson 45 (2x 13 AWG + 2x 18 AWG each)

2) BBSHD:

  • approx. 80 cm High Flex battery cable XT60 to Anderson 45 (13+18 AWG)
  • approx. 70 cm phase cable (MT60), reverb cable (JST), compatible with BBSHD
  • approx. 150 cm from Phaserunner to Cycle Analyst V3 (8-pin connector, with JST on request)

Temperature sensor and PAS are taken over by the BBSHD and can only be used in combination with the Cycle Analyst V3.

3) Standard:

  • approx. 80 cm High Flex battery cable XT60 to Anderson 45 (2x 13 AWG + 2x 18 AWG each)
  • approx. 115 cm phase/reverb cable from MT60 to Anderson 45 (12 AWG) and 2x JST for reverb

4) HiGo Z910

  • approx. 80 cm High Flex battery cable XT60 to Anderson 45 (13+18 AWG)
  • approx. 97 cm phase/reverb cable from MT60 and JST to 9pin HiGo Z910 socket (motor side)

To the Phaserunner controller (currently not available):

  • Dimensions (L x W x H): 99 x 40 x 34 mm
  • Weight: 0.26 kg
  • Max battery amperes: 50 A
  • Battery range: 30V to 90V (21S Li-Ion, 24s LiFe)
  • Low-voltage switch-off: programmable
  • MOSFETs 6X 100V, 3mOhm
  • Made in Canada by Grin

Requires PC configuration to configure the motor, the USB>TTL communication cable is required (same for CA, Satiator)

The controller is ideally suited for the operation of brushless motors for electric vehicles in the power range of 500-2000 watts, with smooth response of an FOC with a torque controller. This controller was developed as a universal device that fits on almost any bicycle frame and can handle almost any motor system. Is compatible with a 24V – 72V battery, with a peak phase current of over 90 amps. Continuous current capability without additional heat sink is typically 45-50 amps. Includes throttle input, cycle analyst and programming plug. Optional cable to motor and battery.

Properties

  • Remote on/off switch
  • Direct connector for V2 and V3 Cycle Analyst
  • Proportional regeneration available through gas inlet or separately
  • Works with or without Hall sensors and even with very high eRPMs (60,000 eRPM +)
  • Waterproof, 100% encapsulated electronics
  • Fully programmable parameters (rain voltage, maximum phase and battery currents, etc.)
  • Field Weakening enables motors to be operated faster than the normal back EMF limit
  • Higher motor efficiency at low speeds / high torques
  • Torque-based throttle lever command (no twitching throttle lever with powerful system)
  • Automatic temperature control to prevent the controller from overheating

Further information and software on the GRIN website

and at Endless Sphere

Views: 30

Important Note:
Making any changes to the manufacturer's original connectors will void the warranty.

Customer ratings

Reviews

There are no reviews yet.

Be the first to review “Cable set for Phaserunner motor controller”

Your email address will not be published. Required fields are marked *

[sibwp_form id=3]