HubSink V2 heatsink for direct motors with thermal paste

(4 customer reviews)

131,09 € incl. VAT, plus shipping

Derzeit nicht verfügbar
Here you can find heat sinks for cooling hub motors | Original GRIN product.

Out of stock

SKU: 2227 Category:
Description

Cooling for the hub motor

Improve the performance and thermal management of your hub motor with this product. With an impressive increase in heat dissipation of up to 200%, Hubsink is the ideal solution. These cooling fins fit motors with 222 mm ØD magnet ring and at least 18 mm clearance between spoke flanges such as MXUS, QS205, Leaf, Crystalyte, 9C. The black anodizing also improves the emission factor and ensures an attractive appearance.

The following steps must be observed during installation:

  • Step 1: Thoroughly clean the outer surface of the ring magnet to remove dirt and oil before applying the thermal paste. Avoid petroleum-based cleaners such as WD40 or automotive degreasers, as they can impair the effectiveness of the thermal paste. Take care to keep the surface free of foreign matter and do not touch it with your cleaned fingers or other materials so as not to impair the thermal interface.

  • Step 2: Test the fit of the hub link around the hub with the supplied fixing nuts and bolts until no more movement can be felt.

  • Step 3: Apply a generous amount of thermal paste to the HubSink and press it firmly onto the hub – preferably with a slight twist to distribute the paste completely.

  • Step 4: After a test drive, it is advisable to allow the engine to heat up. Then tighten the screws again to ensure optimum performance.

With the HubSink, you can optimize the heat management and performance of your wheel hub motor and benefit from a simple and effective solution for improving heat dissipation. However, it is important that the engine diameter matches – otherwise the HubSink ribs cannot be fitted.

Views: 157
Additional information
Weight0,6 kg
Kompatibel mit
Typ / Verwendung
Brand
Reviews (4)

4 reviews for HubSink V2 heatsink for direct motors with thermal paste

  1. German

    David Wang (verified owner) –

  2. German

    David Wang (verified owner) –

  3. German

    Jurij Donhauser (verified owner) –

    Ich empfehle den HubSink V2 jedem , der mehr Leistung aus dem Motor rauspressen will !!! Ich fahre den MXUS 3K-Turbo 4T , befüllt mit Statorade Ferrofluid bei 8KW Leistung . Beim häufiger Beschleunigung oder bei hoher , dauerhafter Geschwindigkeit wurde der Motor nach einiger Zeit zu heiß . Das ist aber keine Überraschung , weil dieser Motor nur für 3KW ausgelegt ist . Aus diesem Grund habe ich den HubSink V2 bei FASTERBIKES bestellt und das war eine super Entscheidung . Jetzt dauert es deutlich länger bis die Temperatur im Motor steigt und sie sinkt auch schneller . Die Temperatur im Motor ist jetzt im Durchschnitt mindestens 20° Celsius niedriger als bei der gleiche Fahrweisen ohne den HubSink V2 . Der Motor ist meiner Erfahrung nach auch etwas effizienter geworden , weil er nicht so heiß wird . Bei der Installation empfehle ich , es mit zwei Personen zu schrauben . Der eine hält fest und der Andere Schraubt ruhig . HubSink V2 ist sein Geld wert . Jetzt kann ich noch mehr spaß haben , ohne , dass ich ständig auf die Temperatur Anzeigen schauen muss .

  4. German

    Jurij Donhauser (verified owner) –

    Ich empfehle den HubSink V2 jedem , der mehr Leistung aus dem Motor rauspressen will !!! Ich fahre den MXUS 3K-Turbo 4T , befüllt mit Statorade Ferrofluid bei 8KW Leistung . Beim häufiger Beschleunigung oder bei hoher , dauerhafter Geschwindigkeit wurde der Motor nach einiger Zeit zu heiß . Das ist aber keine Überraschung , weil dieser Motor nur für 3KW ausgelegt ist . Aus diesem Grund habe ich den HubSink V2 bei FASTERBIKES bestellt und das war eine super Entscheidung . Jetzt dauert es deutlich länger bis die Temperatur im Motor steigt und sie sinkt auch schneller . Die Temperatur im Motor ist jetzt im Durchschnitt mindestens 20° Celsius niedriger als bei der gleiche Fahrweisen ohne den HubSink V2 . Der Motor ist meiner Erfahrung nach auch etwas effizienter geworden , weil er nicht so heiß wird . Bei der Installation empfehle ich , es mit zwei Personen zu schrauben . Der eine hält fest und der Andere Schraubt ruhig . HubSink V2 ist sein Geld wert . Jetzt kann ich noch mehr spaß haben , ohne , dass ich ständig auf die Temperatur Anzeigen schauen muss .

Show only reviews in English (0)

Add a review

Your email address will not be published. Required fields are marked *

Is any information missing here?

The email address is optional and only used so that we can reply to you.

[sibwp_form id=3]